serv ~ # lspci
00:00.0 Host bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333]
00:01.0 PCI bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333 AGP]
00:09.0 Network controller: Broadcom Corporation BCM4303 802.11b Wireless LAN Controller (rev 02)
00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
00:0c.0 Network controller: RaLink RT2500 802.11g Cardbus/mini-PCI (rev 01)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8233 PCI to ISA Bridge
00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:11.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1b)
00:11.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1b)
00:11.4 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1b)
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 30)
01:00.0 VGA compatible controller: nVidia Corporation NV11 [GeForce2 MX/MX 400] (rev b2)

serv ~ # uname -a
Linux serv 2.6.25-gentoo-r7 #7 SMP Sat Sep 20 13:34:51 CEST 2008 i686 AMD Duron(tm) processor AuthenticAMD GNU/Linux

ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5
phy0 -> rt2500pci_validate_eeprom: EEPROM recovery - NIC: 0xfff0
phy0 -> rt2x00_set_chip: Info - Chipset detected - rt: 0201, rf: 0003, rev: 00000004.
b43legacy-phy1: Broadcom 4301 WLAN found
b43legacy-phy1 debug: Found PHY: Analog 0, Type 1, Revision 4
b43legacy-phy1 debug: Found Radio: Manuf 0x17F, Version 0x2053, Revision 2
phy0: Selected rate control algorithm 'pid'
phy0: Failed to initialize wep
b43legacy-phy1 debug: Radio initialized
b43legacy-phy1 debug: DebugFS (CONFIG_DEBUG_FS) not enabled in kernel config
phy1: Selected rate control algorithm 'pid'
phy1: Failed to initialize wep
phy0 -> rt2x00lib_probe_dev: Error - Failed to initialize hw.
ACPI: PCI interrupt for device 0000:00:0c.0 disabled
rt2500pci: probe of 0000:00:0c.0 failed with error -12
b43legacy: probe of ssb0:0 failed with error -12
Broadcom 43xx-legacy driver loaded [ Features: PID, Firmware-ID: FW10 ]
EXT3 FS on hda6, internal journal
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 265032k swap on /dev/hda7.  Priority:-1 extents:1 across:265032k
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
eth0: no IPv6 routers present

b43legacy-phy1: Broadcom 4301 WLAN found

* Messages for package net-wireless/rt2500-1.1.0_pre2007071515:

 *
 * ERROR: net-wireless/rt2500-1.1.0_pre2007071515 failed.
 * Call stack:
 *               ebuild.sh, line   49:  Called src_compile
 *             environment, line 3115:  Called linux-mod_src_compile
 *             environment, line 2378:  Called die
 * The specific snippet of code:
 *               eval "emake HOSTCC=\"$(tc-getBUILD_CC)\"                                               CC=\"$(get-KERNEL_CC)\"           LDFLAGS=\"$(get_abi_LDFLAGS)\"                                           ${BUILD_FIXES}                                          ${BUILD_PARAMS}                                            ${BUILD_TARGETS} " || die "Unable to emake HOSTCC="$(tc-getBUILD_CC)" CC="$(get-KERNEL_CC)" LDFLAGS="$(get_abi_LDFLAGS)" ${BUILD_FIXES} ${BUILD_PARAMS} ${BUILD_TARGETS}";
 *  The die message:
 *   Unable to emake HOSTCC=i486-pc-linux-gnu-gcc CC=i486-pc-linux-gnu-gcc LDFLAGS=  -C /usr/src/linux M=/var/tmp/portage/net-wireless/rt2500-1.1.0_pre2007071515/work/rt2500-cvs-2007071515/Module modules